Go Back   2023 2024 MBA > MBA > Main Forum

  #1  
Old 31st October 2012, 01:27 PM
OIhjh-GHfghg
Guest
 
Default PSU Entrance Papers

Can you provide me the previous entrance exam paper of Public Sector Units because I have need of its previous exam entrance papers for do preparation of its current entrance exam so tell you for do provide me that.
Reply With Quote Quick reply to this message
  #2  
Old 1st November 2012, 09:40 AM
Super Moderator
 
Join Date: May 2012
Default Re: PSU Entrance Papers

Here I am giving you Public Sector Units of BHEL Electrical Question Papers as below:-

1. The ratio of two specific heats of air is equal to. = 1.41
2. An engine operates between temperature of 9000K and T2 and another engine between T2 and 8000K. For both to do equal work, value of T2 will be. = 6500K

3. A perfect gas at 270C is heated at constant pressure till its volume is double. The final temperature is = 3270C

4. Internal energy of a substance depends on = Temperature

5. Work done in compressing 1kg of gas adiabatically from p1,V1,T1 to p2, V2, T2 is equal to = Cv(T2-T1)
6. Indicated power of a 4-stroke engine is equal to = pLAN/2

7. The unit of entropy is = J/kg 0K

8. Which of the following is not an internal combustion engine : a) 2 stroke petrol engine b)4 stroke petrol engine c) Diesel engine d) steam engine e) Gas turbine. = (d)
9. Air fuel ratio in a jet engine is = 60:1
10. If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a) exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high d) engine starts overheating e) all of the above. = (e)
11. A distributor in spark ignition engines performs the function of : = Providing the correct firing order in engine
12. The spark plug gap is normally maintained at: = 0.45 to 0.6mm

13. Which of the following does not relate to C.I. engine:: a) fuel pump b) fuel injector c) governor d) carburetor e) flywheel = (d)

14. What is the value of Prandtl No.?

15. In domestic refrigerator, the tubes at the back of the refrigerator are: a) evaporator b) condenser c) capillary tubes d)………
16. Wet bulb temperature is. = indication of amount of moisture in air

17. Which refrigerants has the highest critical point temperature. = Freon-11

18. On psychrometric chart, dry bulb temperature lines are. = Vertical

19. The line of action of the buoyant force acts through the. =centroid of the displaced volume of fluid
20. Surface tension has the units. = newtons/m
21. A pressure of 25m of head of water is equal to. =245kN/m2


22. For a submerged body to be in stable equilibrium, the centre of gravity should be. =Below the centre of buoyancy.
23. Runaway speed of a hydraulic turbine is: = the speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open.


24. The actual velocity at vena contracta for flow through an orifice from a reservoir of height H=?. =Cvv2gH


25. 100KW is to be transmitted by each of two separate shafts. A is turning at 250rpm and B at 300rpm. Which shaft must have greater diameter.: = B


26. In a free vortex motion: = each particle moves in a circular path with a speed varying inversely as the distance from the centre.


27. A centrifugal pump has speed-1000rpm, Flow-1200l.p.m, Head-20m, Power-5H.P. If its speed is increased to 1500rpm, new flow will be.: = 1800l.p.m


28. 10m of water column is equal to = 100kN/m2


29. M.I. of a circular area about an axis perpendicular to the area is: = pr4/2


30. A projectile is fired at an angle ? to the vertical. Its horizontal range will be maximum when ? is . =450


31. An elevator weighing 1000kg attains an upward velocity of 4m/sec in two seconds with uniform acceleration. The tension in the supporting cables will be = 1200kg.


32. A 13m ladder is placed against a smooth vertical wall with its lower end 5m from the wall. What should be the co-efficient of friction between ladder and floor so that it remains in equilibrium. = 0.21
33. Sintered and tungsten carbides can be machined by: = EDM


34. A car is moving with a velocity of 60km/hr and possesses energy of 5x105 joules. The mass of the car will be. =3000kg.


35. A beam of length l, having uniform load w kg/unit length is supported freely at the ends. The moments at mid span will be: = wl2/8. http://www.ChetanaS.org
36. A boiler shell 200cm dia and plate thickness 1.5cm is subjected to internal pressure of 1.5MN/m2, then the hoop stress will be. = 100N/m2
37. A body weighing 2kg in air weights 2.5kg when submerged in water. Its specific gravity is. = 6


38. Two identical leaf springs of spring constant k are arranged like cantilevers in parallel and attached at free end by a spring of spring constant k. The equivalent spring constant of combination is; = 1.5k.

39. Automobile steering gear is an example of: = lower pair.
40. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR


41. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.

42. Two cars travel in the same direction at
40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?

43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.


44. Brittle coating technique is used for: = experimental stress analysis.


45. Factor of safety is the ratio of: = yield stress/working stress.


46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.


47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel


48. The product of Cupola is called: = cast iron


49. Brinell tester uses a hardness steel ball of size: = 10mm


50. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.


51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.


52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.
53. PERT is: = event oriented technique


54. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.


55. Bar charts are suitable for: = minor works.
56. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.


57. ----- on a PERT/CPM chart represents: = a significant event representing some mile-stone


58. Electron volt is the unit of : = Energy.
59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.
60. Seamless tubes are made by?


61. Why DC current is not used in transformer?


62. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.


63. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?

39. Automobile steering gear is an example of: = lower pair.
40. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR


41. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.
42. Two cars travel in the same direction at 40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?
43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.


44. Brittle coating technique is used for: = experimental stress analysis.


45. Factor of safety is the ratio of: = yield stress/working stress.


46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.


47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel


48. The product of Cupola is called: = cast iron


49. Brinell tester uses a hardness steel ball of size: = 10mm


50. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.


51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.


52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.
53. PERT is: = event oriented technique


54. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.


55. Bar charts are suitable for: = minor works.
56. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.


57. ----- on a PERT/CPM chart represents: = a significant event representing some mile-stone


58. Electron volt is the unit of : = Energy.
59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.
60. Seamless tubes are made by?


61. Why DC current is not used in transformer?


62. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.


63. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?
Reply With Quote Quick reply to this message
  #3  
Old 1st November 2012, 09:40 AM
Super Moderator
 
Join Date: May 2012
Default Re: PSU Entrance Papers

Here I am giving you Public Sector Units of BHEL Electrical Question Papers as below:-

1. The ratio of two specific heats of air is equal to. = 1.41
2. An engine operates between temperature of 9000K and T2 and another engine between T2 and 8000K. For both to do equal work, value of T2 will be. = 6500K

3. A perfect gas at 270C is heated at constant pressure till its volume is double. The final temperature is = 3270C

4. Internal energy of a substance depends on = Temperature

5. Work done in compressing 1kg of gas adiabatically from p1,V1,T1 to p2, V2, T2 is equal to = Cv(T2-T1)
6. Indicated power of a 4-stroke engine is equal to = pLAN/2

7. The unit of entropy is = J/kg 0K

8. Which of the following is not an internal combustion engine : a) 2 stroke petrol engine b)4 stroke petrol engine c) Diesel engine d) steam engine e) Gas turbine. = (d)
9. Air fuel ratio in a jet engine is = 60:1
10. If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a) exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high d) engine starts overheating e) all of the above. = (e)
11. A distributor in spark ignition engines performs the function of : = Providing the correct firing order in engine
12. The spark plug gap is normally maintained at: = 0.45 to 0.6mm

13. Which of the following does not relate to C.I. engine:: a) fuel pump b) fuel injector c) governor d) carburetor e) flywheel = (d)

14. What is the value of Prandtl No.?

15. In domestic refrigerator, the tubes at the back of the refrigerator are: a) evaporator b) condenser c) capillary tubes d)………
16. Wet bulb temperature is. = indication of amount of moisture in air

17. Which refrigerants has the highest critical point temperature. = Freon-11

18. On psychrometric chart, dry bulb temperature lines are. = Vertical

19. The line of action of the buoyant force acts through the. =centroid of the displaced volume of fluid
20. Surface tension has the units. = newtons/m
21. A pressure of 25m of head of water is equal to. =245kN/m2


22. For a submerged body to be in stable equilibrium, the centre of gravity should be. =Below the centre of buoyancy.
23. Runaway speed of a hydraulic turbine is: = the speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open.


24. The actual velocity at vena contracta for flow through an orifice from a reservoir of height H=?. =Cvv2gH


25. 100KW is to be transmitted by each of two separate shafts. A is turning at 250rpm and B at 300rpm. Which shaft must have greater diameter.: = B


26. In a free vortex motion: = each particle moves in a circular path with a speed varying inversely as the distance from the centre.


27. A centrifugal pump has speed-1000rpm, Flow-1200l.p.m, Head-20m, Power-5H.P. If its speed is increased to 1500rpm, new flow will be.: = 1800l.p.m


28. 10m of water column is equal to = 100kN/m2


29. M.I. of a circular area about an axis perpendicular to the area is: = pr4/2


30. A projectile is fired at an angle ? to the vertical. Its horizontal range will be maximum when ? is . =450


31. An elevator weighing 1000kg attains an upward velocity of 4m/sec in two seconds with uniform acceleration. The tension in the supporting cables will be = 1200kg.


32. A 13m ladder is placed against a smooth vertical wall with its lower end 5m from the wall. What should be the co-efficient of friction between ladder and floor so that it remains in equilibrium. = 0.21
33. Sintered and tungsten carbides can be machined by: = EDM


34. A car is moving with a velocity of 60km/hr and possesses energy of 5x105 joules. The mass of the car will be. =3000kg.


35. A beam of length l, having uniform load w kg/unit length is supported freely at the ends. The moments at mid span will be: = wl2/8. http://www.ChetanaS.org
36. A boiler shell 200cm dia and plate thickness 1.5cm is subjected to internal pressure of 1.5MN/m2, then the hoop stress will be. = 100N/m2
37. A body weighing 2kg in air weights 2.5kg when submerged in water. Its specific gravity is. = 6


38. Two identical leaf springs of spring constant k are arranged like cantilevers in parallel and attached at free end by a spring of spring constant k. The equivalent spring constant of combination is; = 1.5k.

39. Automobile steering gear is an example of: = lower pair.
40. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR


41. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.

42. Two cars travel in the same direction at
40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?

43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.


44. Brittle coating technique is used for: = experimental stress analysis.


45. Factor of safety is the ratio of: = yield stress/working stress.


46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.


47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel


48. The product of Cupola is called: = cast iron


49. Brinell tester uses a hardness steel ball of size: = 10mm


50. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.


51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.


52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.
53. PERT is: = event oriented technique


54. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.


55. Bar charts are suitable for: = minor works.
56. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.


57. ----- on a PERT/CPM chart represents: = a significant event representing some mile-stone


58. Electron volt is the unit of : = Energy.
59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.
60. Seamless tubes are made by?


61. Why DC current is not used in transformer?


62. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.


63. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?

39. Automobile steering gear is an example of: = lower pair.
40. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR


41. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.
42. Two cars travel in the same direction at 40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?
43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.


44. Brittle coating technique is used for: = experimental stress analysis.


45. Factor of safety is the ratio of: = yield stress/working stress.


46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.


47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel


48. The product of Cupola is called: = cast iron


49. Brinell tester uses a hardness steel ball of size: = 10mm


50. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.


51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.


52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.
53. PERT is: = event oriented technique


54. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.


55. Bar charts are suitable for: = minor works.
56. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.


57. ----- on a PERT/CPM chart represents: = a significant event representing some mile-stone


58. Electron volt is the unit of : = Energy.
59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.
60. Seamless tubes are made by?


61. Why DC current is not used in transformer?


62. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.


63. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?
Reply With Quote Quick reply to this message
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
BHU MCA entrance question papers amrita Main Forum 2 30th June 2021 03:16 PM
PU LLB Entrance Sample Papers Unregistered Main Forum 1 7th October 2016 01:46 PM
IGIDR Entrance Papers Unregistered Main Forum 0 9th July 2015 01:17 PM
Odisha Joint Entrance Examination MCA entrance exam previous year question papers Unregistered Main Forum 1 20th October 2014 10:48 AM
NID Entrance Papers sonu johnym Main Forum 1 4th April 2013 10:54 AM
MBA Entrance Test Papers Pdf mohdnsh singh Main Forum 1 11th February 2013 05:31 PM
JNU Entrance Papers MCA jhony Main Forum 1 8th February 2013 05:20 PM
ISRO entrance papers hannumana Main Forum 1 23rd January 2013 04:02 PM
MSC Chemistry Entrance Papers sheeail Main Forum 1 14th December 2012 01:49 PM
DSE Entrance Papers Unregistered Main Forum 1 10th December 2012 10:36 AM
ISI Entrance Papers Unregistered Main Forum 1 8th December 2012 04:42 PM
MBA entrance papers IGNOU satish aagrawal Main Forum 1 9th November 2012 02:31 PM
ONGC Entrance Papers PANNAKILIl Main Forum 1 9th November 2012 09:35 AM
Law CET Entrance Exam Papers heenahasan.2 Main Forum 1 29th October 2012 03:16 PM
Entrance Question Papers MBBS Entrance sameer45 Main Forum 1 16th October 2012 04:58 PM
Entrance Question Papers For MBA vishala B.Mallapur.p Main Forum 1 29th September 2012 09:10 AM
Entrance Sample Papers BBA wanitashha14 Main Forum 1 20th August 2012 04:10 PM
MBA CET Entrance Exam Papers dore mon Main Forum 1 16th August 2012 11:02 AM
CDAC Entrance Papers sachinkumar Main Forum 1 11th July 2012 04:29 PM
Entrance Questions Papers MCA arun15mar Main Forum 1 25th May 2012 12:23 PM


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5.5. The time now is 02:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.6.0 PL2

1 2