Go Back   2023 2024 MBA > MBA > Main Forum

  #1  
Old 18th October 2014, 02:34 PM
Unregistered
Guest
 
Default BHEL Exam Previous Question Papers

Please provide me question paper for Bharat Heavy Electricals Ltd recruitment examination as soon as possible ?
Reply With Quote Quick reply to this message
  #2  
Old 20th October 2014, 09:15 AM
Super Moderator
 
Join Date: May 2012
Default Re: BHEL Exam Previous Question Papers

Here I am giving you question paper for Bharat Heavy Electricals Ltd recruitment examination.
Bharat Heavy Electricals Ltd paper
When a inductive coil connected to a 200 V, 50Hz ac supply with 10A current flowing through it dissipates 1000 watts then which of the following will have least value in ohms

a.) Resistanceb.) Reactancec.) Impedance d.) None

Oscillator crystal are made of –

a.) Silicon

b.) Germanium

c.) Quartz

d.) None

For small size, high frequency coils, the most common core material is-a. )Airb. )Ferrite c.) Powdered ion
d.) Steel
If we have a parallel plate capacitor of plate area ‘A’ and plate separatoin t and having a capacity C and a metallic plate r of area A and of negligible thickness is introduced in the capacitor at a distance from either of the two plates as shown in the given figure then the capacity of the capacitor will become –

a.)

b.) C

c.) 2C

d.) 4C

A superconductor is a –

a.) A material showing perfect conductivity and Meissner effect below a critical temperature

b.) A conductor having zero resistance

c.) A perfect conductor with highest di-magnetic susceptibility

d.) A perfect conductor which becomes resistance when the current density through it exceeds a critical value

When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF capacitor then the self capacitance of the inductor would be –

a) 8.05 pF

b) 10.05pF

c.) 16.01pF

d.) 20.01pF

Sparking occur when a load is switched off because the circuit has high –

a.) Inductance

b.) Capacitance

c.) Resistance

d.) None

Sparking between contacts can be reduced by inserting a –

a.) Resistance in the line

b.) Capacitor in series with contacts

c.) Capacitor in parallel with contacts

d.) None

RF amplifier of an A.M. receiver is normally biased in –

a.) Class ‘A’

b.) Class ‘b’

c.) Class ‘C’

d.) None

The value of gate voltage for the operation of enhancement of only N channel MOSFET has to be –

a.) High positive

b.) High negative

c.) Low positive

d.) Zero

The input gate current of a FET is –

a.) a few microamperes

b.) negligibly small

c.) a few milliamperes

d.) a few amperes

In the following fig. with R = 30k, the value of current through 2 K resistor is –

a.) 25 mA
b.) 40 mA
c.) 25/16 mA
d.) 10 mA

A step recovery diode –

a.) has on extremely short recovery time

b.) conducts equally well in both directions

c.) is mainly used as a harmonic generator

d.) is an ideal rectifiers of high frequency signals

In order to get maximum undistorted output signal from CE amplifier with VCC 10V, the value of VCE (Q) should be approximately-

a.) 0.1V

b.) 5V

c.) 10V

d) V

In a FET the electrode, which corresponds to collector in bipolar transistor, is –

a.) source

b.) drain

c.) gate

d.) none

The device which acts like an NPN and a PNP transistor connected base to base and emitter to collector is –a.) Triacb.) UJT c.) Diac
d.) SCR
A typical optical fibre has –

a.) High refractive index core and low refractive index cladding

b.) Low refractive index core and high refractive index cladding

c.) Both a and b

d.) None

In the following figure circuit diagram of an op-amp based is shown. The ratio is equal to –

a.) 9

b.) 11

c.) 10

d.) 21

When a loud speaker is connected across the terminals A and B of the network shown in the fig. then its impedance to obtain maximum power dissipation in it will be – a.) 3 – j1 b.) 3 + j9
c.) 7.5 + j 2.5
d.) 7.5 – j 2.5
In the lattice network, the value of R for the maximum power transfer to the load – a.) 5 b.) 6.5
c.) 8
d.) 9
For a lossy transmission line short circuited at the receiving end, the input impedance is given by (Z0 is the characteristic impedance, Ö is the propagation constant and l is the length of the line-a.) Z0 cot h Ölb.) Z0 cot Öl c.) Z0 tan h.Ö l
d.) Z0 tan Öl
The approximate thickness of the radome wall should be –a.) lb.) l/4 c.) l/2
d.) l/8
A relatively permanent information is stored in

a. ) ROM

b.) RAM

c.) PROM

d.) Volatile memory

The rise time of the RC network shown in the given figure is approximately equal to – b.) RC
c.) 2RC
d.) 4RC
If in the network shown in the fig. initially a steady state is attained by closing the switch ‘s’ and then if the switch is opened at t = 0, then the current i(t) through the inductor will be – a.) cos50tA b.) 2A
c.) 2cos100tA
d.) 2sin50tA
When the p network of figure – I and T-network of figure – II are equivalent then the values of R1, R2 and R3 will be respectively – a) 9W, 6W and 6W b.) 6W, 6W and 9W
c.) 9W, 6W and 9W
d.) 6W, 9W and 6W
When the impedance matrices of a two port networks are given by and , then if these two networks are connected in series then the impedance matrix of the resulting two-port network will be –
d.) indeterminate
Joule/coulomb is the unit of – a.) Electric field potential b.) Potential c .) Charge
d.) None of the above
The electric field line and equipotential lines-

a.) Are parallel to each other

b.)Are one and same

c.) Cut each other orthogonally

d.)Can be inclined to each other at any angle

For a lossy transmission line short circuited at the receiving end, the input impedance is given by (When Z0 is the characteristic impendence g is the propagation constant and L is the length of the line
When two equal positive point charges are placed along X- axis at X1 and –X1 respectively then the electric field vector at a point P on the positive Y-axis will be directed-

a.) In the +x direction

b.) In the –x direction

c. ) In the +y direction

d.) In the –y direction

The directions of and in TEM mode transmission line with respect to the direction of propagation are-

a.) Both and are transverse to the direction of propagation

b.) is and are transverse and h has a component in the direction of propagation

c.) is entirely transverse and has a component in the direction of propagation

d. ) is entirely transverse and has a component in the direction of propagation

The lowest TM mode in a rectangular waveguide of cross –section a x b with a>b will be-

a.) TM01

b.)TE10

c.) TM112

d.)TE11

When a transmitter in a free space radiates a mean power of ‘p’ watts uniformly in all directions then at a distance d sufficiently far from the source in plane the electric field E should be related to p and d as –
. When a dipole antenna was radiating with some excitation in free space radiating a certain amount of the power v if then this antenna is immersed in a lake where water is non-dissipative but has a dielectric constant of 81, then the radiated power with the same excitation will be

a.) Decrease to finite non-zero value

b.)Remain the same

c. )Increase

d.)Decrease to zero

When a (75 – j40)W load is connected to a coaxial line of Z0 = 75 W at 6MHz then the load matching on the line can be accomplished by connecting-

a.) A short – circuited stub at the load

b.)An inductance at the load

c. )A short circuited stub at a specific distance from the load

d.)none of the above

As compared to analog multimeters, digital multimeters are –a.) less accurateb.) more accurate c.) equally accurate
d.) none.
When a signal of 10 mV at 75 MHz is to be measured then which of the following instruments can be used –a.) VTVMb.) Cathode ray oscilloscope c.) Moving iron voltmeter
d.) Digital multimeter
Which of the following statement is true about two wattmeter method for power measurement in three phase current ?a.) power can be measured using two wattmeter method only for star connected three phase circuits.b.) when two meter show indentical readings, in the power factor is 0.5. c.) when power factor is unit, one of the wattmeter reads zero
d.) when the reading of the two wattmeters are equal but of opposite sign, then the power factor is zero –
When a capacitance transducer has two plates of area 5cm2 each, separated by an air gap of 2mm than the displacement sensitivity in pf/cm due to gap change would be –a.) 11.1b.) 44.2 c.) 52.3
d.) 66.3
The Q of a radio coil –a.) is independent of frequencyb.) increases monotonically as frequency increases c.) decreases monotonically as frequency increases
d.) increases upto a certain frequency and then decreases beyond that frequency
When a generator of internal impedance and operating at 1GHz feeds a load via a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed line is –a.) 0.5b.) 1.5 c.) 2.5
d.) 1.75
The coding system typically used in digital telemetry is –a.) PPM (pulse position modulation)b.) PAM (pulse amplitude modulation) c.) PCM (pulse code modulation)
d.) PDM (pulse duration modulation)
Radiation pyrometers are used for the measurement of temperature in the range of –

a.) -2000C to 5000C

b.) 00C to 5000C

c.) 5000C to 12000C

d.) 12000C to 25000C

In the given figure band structure is shown. It is of –

a.) Gallium Avesenide (GaAs)

b.) Silicon (Si)

c.) Copper (Cu)

d.) Germanium (Ge)

When anode is positive with respect to cathode in an SCR, the numbers of blocked p-n junction is –

a.) 1

b.) 2

c.) 3

d.) 4

The circuit symbol for a GTO is

a. b.

c. d.

In the given fig. mark out the type of Cyclo converters

a.) 1 phase to 1 phase with continuous conduction
b.) 1 phase to 1 phase with discontinuous conduction
c.) step up device
d.) 3 phase to 1 phase device

In the given fig. A-1, C=5, m H and C=20 m F, C is initially charged to 200 V. After the switch.
S is closed at t = 0 the
maximum value of current and the
time at which it reaches this value are respectively.

a.) 400 A, 15.707 mS

b.) 50 A, 30 mSc.) 100 A, 62.828 mSd.) 400 A, 31.414 mS

Bharat Heavy Electricals Ltd paper
1)Unit of Entropy (J/kg K or kJ/kg K)

2)A mass of 100kg is falling from a height of 1 m and penetrates the sand into for 1 m. What is the resistance force given by sand.

3)Ratio of specific heats of air. (1.41)

4)A body weighs 3 kg in air. If it is submerged in a liquid, it weighs 2.5 kg. What is the specific gravity of the liquid.

5)Two cars travell in same direction at 40 km/hr at a regular distance. A car comes in a opposite direction in 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between them?

6)A simple problem involing in hoops stress. For sphere: M= [3/2]*p*V*[density of pressure vessel material/Maximum working stress it can tolerate] For Thin walled pressure walls: Hoops stress or stress in the radial direction =p*r/2t

7)A problem in force calculation in a body moving in a inclined surface.

8)Composition of bronze. (Copper+zinc)

9)Compostion of stainless steel.(iron+chromium+nickel+carbon)

10)CI is manifactured in which process. (cupola process) 11)What percentage of carbon is preset in pig iron. (4.5 to 6%)

12)Water is available at 10m height. What is the pressure available? (pressure=density*g*height; p=1000*9.81*10; p=98100N/m2) Ch

13)What will happen if the speed of the centrifugal pump doubles.

14)The unit eV is widely used in ? (Nuclear and atomic physics)

15)What will happen to the resistance, when the diameter of the conductor is doubled?

16)The power comsumed by a electrical device is 1000W at 250V, What is the resistance in the device? (Power= Voltage*current; Current=Power/Voltage, Current,I=1000/250=4 amps. V=IR, Therefore R=250/4=62.5 ohms)

17)Why DC current is not used in transformer.

18)On what principle the sonar/ radar works?

19)Bending moment diagram for the UDL is in what shape?

20)Function of the distributor in petrol vehicles? (Spark timing) 21)Which is not present in CI engines? (carburrettor)

22)What will happen if one cylinder recieves more amount of fuel spray from injectors than other injectors?

23)Purpose of draft tube in hydraulic turbines? (The purpose of a draft tube is toconvert some of the kinetic energy of the flow from the runner (the rotating part of the turbine) intopressure energy and thereby increase the efficiency ofthe hydro power turbine.)

24)What is the effect or reheater in the gas turbine? (The advantage of reheater is significantly increased thrust; the disadvantage is it has very high fuel consumption and inefficiency) )Problems involving with fricition coefficient.

26)Factor of safety = Yeild stress/Working stress. 27)Which is the example of non parallel power transmission (Universal coupling) 28)For perpendicular shafts worm gear is used.

29)A planet gear with 25 teeth is meshed with a sun gear of 100 teeth. Both are connected using a arm. How many rotations are needed for planet gear to complete one rotation around the sun gear?

30)What is equivalent spring constant for spring in parallel?

31) Some questions was asked related to boundry layer and vortex flow.

32) 5 questions were asked in PERT, Process planning, Product planning, Break even analysis.

33)How are tungsten and sintered composite materials are machined? (Electro Discharge Machining, EDM)

Last edited by Arvind Kumar; 20th October 2014 at 09:17 AM.
Reply With Quote Quick reply to this message
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
LIC AAO Exam Previous Year Question Papers Free Download Unregistered Main Forum 2 4th April 2018 09:13 PM
RBI Assistant Exam Previous Year Question Papers With Answers Unregistered Main Forum 1 4th November 2016 02:55 PM
Polytechnic Entrance Exam Previous Question Papers Unregistered Main Forum 1 27th October 2016 10:26 AM
AIIMS Entrance Exam Previous Question Papers Unregistered Main Forum 1 25th October 2016 01:35 PM
Kanbay Placement Exam Previous Years Question Papers Unregistered Online MBA Discussions 1 21st November 2015 06:56 PM
Bank of Baroda PO exam previous year solved question papers Unregistered Main Forum 1 13th November 2015 05:41 PM
Accenture Placement Exam Previous Years Question Papers Unregistered Main Forum 1 13th November 2015 03:03 PM
Bank exam previous years question papers with answers Unregistered Main Forum 1 12th November 2015 01:33 PM
Mumbai University B.Com Exam Previous Years Question Papers Unregistered Main Forum 1 9th November 2015 05:33 PM
Bank Clerk Exam Previous years Question Papers Unregistered Main Forum 1 9th November 2015 03:04 PM
Philips Previous Year Placement Exam Question Papers Unregistered Main Forum 1 9th November 2015 01:59 PM
Previous question papers of SBI Clerk exam Unregistered Main Forum 0 17th July 2015 03:13 PM
NEET Exam Previous Year Question Papers Unregistered Main Forum 0 11th July 2015 12:39 PM
SCRA Exam Previous Question Papers Unregistered Main Forum 1 27th October 2014 04:03 PM
Power Grid Exam Previous question papers Unregistered Main Forum 1 21st October 2014 10:18 AM
Previous year question papers of BHEL Supervisor Trainee Exam of Diploma in Mechanica Unregistered Main Forum 1 20th October 2014 01:49 PM
Previous year Civil Service Mains exam question papers of LAW Unregistered Main Forum 1 20th October 2014 12:05 PM
Rajasthan Police Constable Exam Previous question papers Unregistered Main Forum 1 20th October 2014 09:57 AM
Previous year question papers of HCS Mains Exam Unregistered Main Forum 1 11th October 2014 05:23 PM
Previous year question papers for Postal Assistant Exam Unregistered Main Forum 1 11th October 2014 04:53 PM


Quick Reply
Your Username: Click here to log in

Message:
Options

Thread Tools Search this Thread



All times are GMT +5.5. The time now is 10:39 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.6.0 PL2

1 2